Turn Ignition switch to OFF & Run/Stop switch is to Run.
• Push odometer reset button in & hold.
• Turn ignition switch to Ignition and release odometer reset button. Background lighting should illuminate, speedometer needle should sweep its full range and indicator lamps (battery, security, low fuel, check engine and cruise) should illuminate. The word “diag” should then appear.
• Push the odometer reset button once and you will see the selection menu "PSSPtb" with the first P flashing.
• Each letter represents an area of the diagnostics module. The module that is flashing is the one you are going to check. To move from one letter (module) to the next, you push the odometer reset button one time. (from P to S to SP to t to b and back to P, etc.)
P --> ECM (Electronic Control Module [EFI])
S --> TSM/TSSM/HFSM (Turn Signal/ Turn Signal Security Module/ Hands-free Security Module)
SP --> speedometer
t --> tachometer
b --> ABS codes
• To get the DTC within an area of diagnostics, push and hold the odometer reset button in for 5 seconds and release. If there are any DTCs the code will be displayed or the word “none” will appear if there are no DTCs. Push the odometer reset button again to view additional codes if they exist.
• Record the codes.
• If DTCs are NOT to be cleared, Press and release the odometer reset button. Part number of module will be displayed.
NOTE: To determine if a code is current or historic, clear the displayed code by pushing in and holding the odometer reset button ( longer than 5 seconds) until 'clear' is displayed. Release the odometer reset button. Turn OFF the ignition switch. Perform a road test then shut your bike down. Recheck the DTC’s again by repeating steps 1 to 7. If the code is current it will reappear. Historic DTCs are stored for 50 ignition cycles before cleared. The security lamp will only indicate the existence of historic DTCs for two ignition cycles.
• If DTCs are to be cleared for that module, press and hold the odometer reset button until 'clear' is displayed.
• Press and release the odometer reset button to continue to the next module.
• Turn Ignition switch to OFF to exit the diagnostic mode.
Always correct the serial data codes (DTC U1300, U1301, U1016, U1040, U1064, U1097, U1255) before resolving any other codes. DTC's are assigned priority numbers to determine the order in which they should be diagnosed. The lowest priority number DTC should be diagnosed first and then continue with the next lowest DTC.
Diagnostic Trouble Codes (DTCs) (TABLE 1)
DTC: B0562
FAULT CONDITION: Battery Voltage Low
SOLUTION: 3.6 DTC B0563, P0562, P0563
DTC: B0563
FAULT CONDITION: Battery Voltage High
PRIORITY ORDER: 138
SOLUTION: 3.6 DTC B0563, P0562, P0563
DTC: B1004
FAULT CONDITION: Fuel Level Sending Unit Low
PRIORITY ORDER: 145
SOLUTION: 4.2 DTC B1004, B1005
DTC: B1005
FAULT CONDITION: Fuel Level Sending Unit High/Open
PRIORITY ORDER: 146
SOLUTION: 4.2 DTC B1004, B1005
DTC: B1006
FAULT CONDITION: Accessory Line Overvoltage
PRIORITY ORDER: 143
SOLUTION: 3.7 DTC B1006, B1007
DTC: B1007
FAULT CONDITION: Ignition Line Overvoltage
PRIORITY ORDER: 142
SOLUTION: 3.7 DTC B1006, B1007
DTC: B1008
FAULT CONDITION: Trip Odometer Reset Switch Closed
PRIORITY ORDER: 144
SOLUTION: 4.3 DTC B1008
DTC: B1121
FAULT CONDITION: Left Turn Output Fault
PRIORITY ORDER: 129
SOLUTION: 5.11 DTC B1121,B1122,B1123,B1124,B1125,B1126
DTC: B1122
FAULT CONDITION: Right Turn Output Fault
PRIORITY ORDER: 130
SOLUTION: 5.11 DTC B1121,B1122,B1123,B1124,B1125,B1126
DTC: B1123
FAULT CONDITION: Left Turn Signal short-to-ground
PRIORITY ORDER: 131
SOLUTION: 5.11 DTC B1121,B1122,B1123,B1124,B1125,B1126
DTC: B1124
FAULT CONDITION: Right Turn Signal short-to-ground
PRIORITY ORDER: 132
SOLUTION: 5.11 DTC B1121,B1122,B1123,B1124,B1125,B1126
DTC: B1125
FAULT CONDITION: Left Turn Signal short-to-voltage
PRIORITY ORDER: 133
SOLUTION: 5.11 DTC B1121,B1122,B1123,B1124,B1125,B1126
DTC: B1126
FAULT CONDITION: Right Turn Signal short-to-voltage
PRIORITY ORDER: 134
SOLUTION: 5.11 DTC B1121,B1122,B1123,B1124,B1125,B1126
DTC: B1131
FAULT CONDITION: Alarm Output Low
PRIORITY ORDER: 139
SOLUTION: 5.18 DTC B1131,B1132
DTC: B1132
FAULT CONDITION: Alarm Output High
PRIORITY ORDER: 140
SOLUTION: 5.18 DTC B1131,B1132
DTC: B1134
FAULT CONDITION: Starter Relay Output High
PRIORITY ORDER: 128
SOLUTION: 5.19 DTC B1134
DTC: B1135
FAULT CONDITION: Accelerometer Fault
PRIORITY ORDER: 23
SOLUTION: 5.12 DTC B1135,B1136,B1141,B1142
DTC: B1136
FAULT CONDITION: Accelerometer tip-over self-test fault
PRIORITY ORDER: 24
SOLUTION: 5.12 DTC B1135,B1136,B1141,B1142
DTC: B1141
FAULT CONDITION: Ignition Switch open/low
PRIORITY ORDER: 141
SOLUTION: 5.12 DTC B1135,B1136,B1141,B1142
DTC: B1142
FAULT CONDITION: Internal Fault
PRIORITY ORDER: 22
SOLUTION: 5.12 DTC B1135,B1136,B1141,B1142
DTC: B1143
FAULT CONDITION: Security antenna short-to-ground
PRIORITY ORDER: 135
SOLUTION: 5.20 DTC B1143,B1144,B1145
DTC: B1144
FAULT CONDITION: Security antenna short-to-battery
PRIORITY ORDER: 136
SOLUTION: 5.20 DTC B1143,B1144,B1145
DTC: B1145
FAULT CONDITION: Security antenna open
PRIORITY ORDER: 137
SOLUTION: 5.20 DTC B1143,B1144,B1145
DTC: B1151
FAULT CONDITION: Sidecar BAS short to ground
PRIORITY ORDER: 25
SOLUTION: See Trike or Sidecar supp manual
DTC: B1152
FAULT CONDITION: Sidecar BAS short to battery
PRIORITY ORDER: 26
SOLUTION: See Trike or Sidecar supp manual
DTC: B1153
FAULT CONDITION: Sidecar BAS Out of Range
PRIORITY ORDER: 27
SOLUTION: See Trike or Sidecar supp manual
DTC: B1154
FAULT CONDITION: Clutch switch short-to-ground
PRIORITY ORDER: 28
SOLUTION: 5.21 DTC B1154,B1155
DTC: B1155
FAULT CONDITION: Neutral Switch short-to-ground
PRIORITY ORDER: 29
SOLUTION: 5.21 DTC B1154,B1155
DTC: C0562
FAULT CONDITION: System Voltage Low
PRIORITY ORDER: 111
SOLUTION: 3.6 DTC B0563,P0562,P0563
DTC: C0563
FAULT CONDITION: System Voltage High
PRIORITY ORDER: 112
SOLUTION: 3.6 DTC B0563,P0562,P0563
DTC: C1014
FAULT CONDITION: ECU internal solid state relay fault
PRIORITY ORDER: 105
SOLUTION: 7.15 DTC C1014,C1055-C1066,C1118,C1121
DTC: C1017
FAULT CONDITION: Pump Motor Power Circuit Open Fault
PRIORITY ORDER: 110
SOLUTION: 7.2 DTC C1017,C1018
DTC: C1018
FAULT CONDITION: Pump motor ground high resistance fault
PRIORITY ORDER: 109
SOLUTION: 7.2 DTC C1017,C1018
DTC: C1021
FAULT CONDITION: Front wheel speed sensor always equals zero kph
PRIORITY ORDER: 115
SOLUTION: 7.3 DTC C1021,C1023
DTC: C1023
FAULT CONDITION: Rear wheel speed sensor always equals zero kph
PRIORITY ORDER: 116
SOLUTION: 7.3 DTC C1021,C1023
DTC: C1025
FAULT CONDITION: Front wheel speed sensor signal intermittent
PRIORITY ORDER: 117
SOLUTION: 7.4 DTC C1025,C1027,C1206,C1208
DTC: C1027
FAULT CONDITION: Rear wheel speed sensor signal intermittent
PRIORITY ORDER: 118
SOLUTION: 7.4 DTC C1025,C1027,C1206,C1208
DTC: C1032
FAULT CONDITION: Front wheel speed sensor circuit open or shorted
PRIORITY ORDER: 113
SOLUTION: 7.5 DTC C1032,C1034
DTC: C1034
FAULT CONDITION: Rear wheel speed sensor circuit open or shorted
PRIORITY ORDER: 114
SOLUTION: 7.5 DTC C1032,C1034
DTC: C1042
FAULT CONDITION: Pump motor open
PRIORITY ORDER: 107
SOLUTION: 7.6 DTC C1042,C1043
DTC: C1043
FAULT CONDITION: Pump motor stalled
PRIORITY ORDER: 108
SOLUTION: 7.6 DTC C1042,C1043
DTC: C1055
FAULT CONDITION: ECU internal fault
PRIORITY ORDER: 96
SOLUTION: 7.15 DTC C1014,C1055-C1066,C1118,C1121
DTC: C1056
FAULT CONDITION: ECU internal fault - sold state relay shorted ON
PRIORITY ORDER: 97
SOLUTION: 7.15 DTC C1014,C1055-C1066,C1118,C1121
DTC: C1057
FAULT CONDITION: ECU internal fault - solid state relay shorted to ground
PRIORITY ORDER: 98
SOLUTION: 7.15 DTC C1014,C1055-C1066,C1118,C1121
DTC: C1061
FAULT CONDITION: ECU internal fault - front apply solenoid
PRIORITY ORDER: 99
SOLUTION: 7.15 DTC C1014,C1055-C1066,C1118,C1121
DTC: C1062
FAULT CONDITION: ECU internal fault - front release solenoid
PRIORITY ORDER: 100
SOLUTION: 7.15 DTC C1014,C1055-C1066,C1118,C1121
DTC: C1065
FAULT CONDITION: ECU internal fault - rear apply solenoid
PRIORITY ORDER: 101
SOLUTION: 7.15 DTC C1014,C1055-C1066,C1118,C1121
DTC: C1066
FAULT CONDITION: ECU internal fault - rear release solenoid
PRIORITY ORDER: 102
SOLUTION: 7.15 DTC C1014,C1055-C1066,C1118,C1121
DTC: C1094
FAULT CONDITION: Front brake switch always on
PRIORITY ORDER: 121
SOLUTION: 7.7 DTC C1094
DTC: C1095
FAULT CONDITION: Front brake switch open
PRIORITY ORDER: 122
SOLUTION: 7.8 DTC C1095
DTC: C1118
FAULT CONDITION: ECU internal fault - front apply solenoid correlation
PRIORITY ORDER: 103
SOLUTION: 7.15 DTC C1014,C1055-C1066,C1118,C1121
DTC: C1121
FAULT CONDITION: ECU internal fault - rear apply solenoid correlation
PRIORITY ORDER: 104
SOLUTION: 7.15 DTC C1014,C1055-C1066,C1118,C1121
DTC: C1151
FAULT CONDITION: Front wheel ABS release too long
PRIORITY ORDER: 126
SOLUTION: 7.9 DTC C1151
DTC: C1153
FAULT CONDITION: Rear wheel ABS release too long
PRIORITY ORDER: 127
SOLUTION: 7.10 DTC C1153
DTC: C1158
FAULT CONDITION: Calibration programming required
PRIORITY ORDER: 106
SOLUTION: 7.11 DTC C1158
DTC: C1206
FAULT CONDITION: Front wheel speed sensor frequency out of range
PRIORITY ORDER: 119
SOLUTION: 7.4 DTC C1025,C1027,C1206,C1208
DTC: C1208
FAULT CONDITION: Rear wheel speed sensor frequency out of range
PRIORITY ORDER: 120
SOLUTION: 7.4 DTC C1025,C1027,C1206,C1208
DTC: C1212
FAULT CONDITION: Front or Rear brake not applied with decel
PRIORITY ORDER: 125
SOLUTION: 7.12 DTC C1212
DTC: C1214
FAULT CONDITION: Rear brake switch always on
PRIORITY ORDER: 123
SOLUTION: 7.13 DTC C1214
DTC: C1216
FAULT CONDITION: Rear brake switch open
PRIORITY ORDER: 124
SOLUTION: 7.14 DTC C1216
DTC: P0031
FAULT CONDITION: O2 heater low/open
PRIORITY ORDER: 82
SOLUTION: 6.7 DTC P0031,P0032,P0131,P0132,P0134,P0151,P0152,P0154
DTC: P0032
FAULT CONDITION: O2 heater shorted/high
PRIORITY ORDER: 82
SOLUTION: 6.7 DTC P0031,P0032,P0131,P0132,P0134,P0151,P0152,P0154
DTC: P0106
FAULT CONDITION: MAP Sensor Rate of Range Error
DTC: P0107
FAULT CONDITION: Map Sensor Open/Low
PRIORITY ORDER: 19
SOLUTION: 6.4 DTC P0107,P0108,P0112,P0113
DTC: P0108
FAULT CONDITION: Map Sensor High
PRIORITY ORDER: 20
SOLUTION: 6.4 DTC P0107,P0108,P0112,P0113
DTC: P0112
FAULT CONDITION: IAT Sensor Voltage Low
PRIORITY ORDER: 58
SOLUTION: 6.4 DTC P0107,P0108,P0112,P0113
DTC: P0113
FAULT CONDITION: IAT Sensor Voltage Open/High
PRIORITY ORDER: 59
SOLUTION: 6.4 DTC P0107,P0108,P0112,P0113
DTC: P0117
FAULT CONDITION: ET Sensor Voltage Low
PRIORITY ORDER: 56
SOLUTION: 6.5 DTC P0117,P0118
DTC: P0118
FAULT CONDITION: ET Sensor Voltage Open/High
PRIORITY ORDER: 57
SOLUTION: 6.5 DTC P0117,P0118
DTC: P0120
FAULT CONDITION: Throttle position sensor 1 range error
PRIORITY ORDER: 38
SOLUTION: 6.6 DTC P0120,P0122,P0123,P0220,P0222,P0223
DTC: P0122
FAULT CONDITION: TP Sensor Open/Low
PRIORITY ORDER: 40
SOLUTION: 6.6 DTC P0120,P0122,P0123,P0220,P0222,P0223
DTC: P0123
FAULT CONDITION: TP Sensor High
PRIORITY ORDER: 41
SOLUTION: 6.6 DTC P0120,P0122,P0123,P0220,P0222,P0223
DTC: P0131
FAULT CONDITION: Front O2 sensor low (lean)
PRIORITY ORDER: 84
SOLUTION: 6.7 DTC P0031,P0032,P0131,P0132,P0134,P0151,P0152,P0154
DTC: P0132
FAULT CONDITION: Front O2 sensor high (rich)
PRIORITY ORDER: 86
SOLUTION: 6.7 DTC P0031,P0032,P0131,P0132,P0134,P0151,P0152,P0154
DTC: P0134
FAULT CONDITION: Front O2 sensor open/not responding
PRIORITY ORDER: 88
SOLUTION: 6.7 DTC P0031,P0032,P0131,P0132,P0134,P0151,P0152,P0154
DTC: P0151
FAULT CONDITION: Rear O2 sensor low (lean)
PRIORITY ORDER: 85
SOLUTION: 6.7 DTC P0031,P0032,P0131,P0132,P0134,P0151,P0152,P0154
DTC: P0152
FAULT CONDITION: Rear O2 sensor high (rich)
PRIORITY ORDER: 87
SOLUTION: 6.7 DTC P0031,P0032,P0131,P0132,P0134,P0151,P0152,P0154
DTC: P0154
FAULT CONDITION: Rear O2 sensor open/not responding
PRIORITY ORDER: 89
SOLUTION: 6.7 DTC P0031,P0032,P0131,P0132,P0134,P0151,P0152,P0154
DTC: P0220
FAULT CONDITION: Throttle position sensor 2 range error
PRIORITY ORDER: 39
SOLUTION: 6.6 DTC P0120,p0122,P0123,P0220,P0222,P0223
DTC: P0222
FAULT CONDITION: Throttle position sensor 2 low/open
PRIORITY ORDER: 42
SOLUTION: 6.6 DTC P0120,p0122,P0123,P0220,P0222,P0223
DTC: P0223
FAULT CONDITION: Throttle position sensor 2 high
PRIORITY ORDER: 43
SOLUTION: 6.6 DTC P0120,p0122,P0123,P0220,P0222,P0223
DTC: P0261
FAULT CONDITION: Front Injector Open/Low
PRIORITY ORDER: 66
SOLUTION: 6.8 DTC P0261,P0262,P0263,P0264
DTC: P0262
FAULT CONDITION: Front Injector High
PRIORITY ORDER: 68
SOLUTION: 6.8 DTC P0261,P0262,P0263,P0264
DTC: P0263
FAULT CONDITION: Rear Injector Open/Low
PRIORITY ORDER: 67
SOLUTION: 6.8 DTC P0261,P0262,P0263,P0264
DTC: P0264
FAULT CONDITION: Rear Injector High
PRIORITY ORDER: 69
SOLUTION: 6.8 DTC P0261,P0262,P0263,P0264
DTC: P0373
FAULT CONDITION: CKP Sensor Intermittent
PRIORITY ORDER: 18
SOLUTION: 6.9 DTC P0373,P0374
DTC: P0374
FAULT CONDITION: CKP Sensor Synch Error
PRIORITY ORDER: 21
SOLUTION: 6.9 DTC P0373,P0374
DTC: P0444
FAULT CONDITION: Purge control open/low
PRIORITY ORDER: 77
SOLUTION: 6.10 DTC P0444,P0445
DTC: P0445
FAULT CONDITION: Purge control high
PRIORITY ORDER: 78
SOLUTION: 6.10 DTC P0444,P0445
DTC: P0501
FAULT CONDITION: VSS Low
PRIORITY ORDER: 72
SOLUTION: 6.11 DTC P0501,P0502
DTC: P0502
FAULT CONDITION: VSS High/Open
PRIORITY ORDER: 73
SOLUTION: 6.11 DTC P0501,P0502
DTC: P0505
FAULT CONDITION: Loss of Idle Sped Control
PRIORITY ORDER: 76
SOLUTION: 6.12 DTC P0505
อยากทราบวิธีการเข้าไปดู DTC Codes Sportster 2010 ครับ (อ่าน 3873 ครั้ง)